Understanding the impact of valve flow coefficient (Cv) in fluid systems

Understanding the impact of valve flow coefficient (Cv) in fluid systems for microelectronics manufacturing

BY STEPHANE DOMY, Saint-Gobain Performance Plastics,

When scaling up, or down, a high-purity liquid installation – many complex factors need to be considered from ensuring the integrity of the transported product to the cleanliness of the environment for both the safety of the process and the operator [1]. In my 15 years working in the semiconductor fluid handling component industry, I’ve learned that the Cv is a bit misunderstood. Given the Cv formula can be used for any flow component in a fluid line, most are familiar with it, yet few consider how it relates to their specific installation. Therefore, this article will focus on factors that pertain to achieving a specific flow performance and specifically the flow coefficient (Cv) as it relates to valves.

Cv empirical explanation and more

As we know, when working on a turbulent flow the Cv formula is: Cv= Q√(SG / ∆P) where Q is the flow going through the valve in gallons per minute (GPM), SG is the specific gravity of the fluid and ∆P is the pressure drop in PSI through the component. In the semiconductor industry, due to the low velocity of the transported fluid the high purity chemistry and slurries are mostly in a semi–turbulent state or a laminar state. Yet you’ll notice there is not a single link to the viscosity of the transported product in the Cv formula. This is significant given the viscosity directly impacts the Cv value when the flow is in a semi-turbulent or laminar mode. Consider that if you calculate the pressure drop in your system with the formula above you could end up with a result that is 4 to 5 times lower. No doubt this inaccuracy can cause significant issues in your installation.

To take this further, let’s analyze how pressure drop based on flow evolves through a valve by comparing a Saint-Gobain Furon® Q-Valve (1⁄2” inner flow path and 1⁄2” pipe connection) to a standard semiconductor industry valve of the same size. The Saint-Gobain valve, which meets the requirements of the semiconductor industry (metal free, 100% fluoropolymer flow path and so on), has a Cv of 3.5 – one of the best for its dimensions. To ease the calculation, we will use deionized (DI) water, which will free us of the specific gravity or impact of the viscosity if we are not in the right state.

As we can see on the graph in FIGURE 1, at a normal flow rate used in micro-e for 1⁄2” 5 to 10 lpm; the pressure drop difference between a standard valve and a Saint-Gobain valve is in the range of 0.1 to 0.3 PSI. At first glance, this does not appear to be much. However, let’s factor in a viscous product and that you have a number of these lines in your flow line — now the numbers start to accumulate. And by moving from a standard valve to a Saint-Gobain valve, as described above, you start to see a significant difference in pressure drop, which could occur across your installation. That being said, up to a certain limit (defined by another component in your installation, such as your pump pressure capability or some more delicate device) an “easy” counter is to increase the pressure through put of your pump but it is at the expense of wasting energy and adding the potential for additional shearing or particle generation in your critical fluid. Now that we have reviewed, the impact of the Cv on our flow and how this could impact our installation, let’s see what can potentially impact the Cv.

Screen Shot 2017-09-26 at 1.32.39 PM

Design impact on Cv and resulting trade-off

The first impact that may come to mind is a larger orifice – and it’s correct. The size of the orifice can benefit flow through and directly relates to the volume of your valve. However there are trade-offs for this improved Cv. The first is cost increase. A higher volume requires a larger valve, which can cost up to 50% more than the initial valve due to specific material and process requirements. Additionally, as highlighted in “Design Impact for Fluid Components” by increasing the size of the component (due to the specific micro-e material requirements), you could lose pressure rating performance [1]. Also when increasing the inner volume of your valve, you potentially increase volume retention as well as particle generation, given that using larger actuation systems results in more points of contact and creates a hub for generating particles. Another possible drawback is significant velocity loss, but that will have to be addressed in another article. The critical point to be taken here is the importance of choosing the right size orifice – too small and flow can be restricted too much and too big and you may end up paying for other problems.

Another potential impact to Cv is the difference in valve technology. Though there more, I’ll specifically cover stopcock/ball valves, weir style valves; and diaphragm valves. Other valve technologies, such as the butterfly valve, will not be discussed because their construction materials are generally not used for fluid handling components for the semiconductor industry.

Starting with the simplest design, the stopcock/ball valve provides by far the best Cv of the three technologies mentioned. Considering the premium Cv achieved, you would assume they are expensive. Instead they are generally the cheapest of the three values mentioned. One drawback in using stopcock valves is the need for a liquid oring on the fluid path which may create compatibility issues. The exception is the Furon® SCM Valve, a stopcock valve that employs a PFA on PTFE technology and allows for oring-free sealing. Additionally, stopcock valves can lower pressure/ temperature ratings and have a tendency to generate a great deal of particles when actuated. This occurs when the key or ball is rotating inside the valve body. Both drawbacks are related to the PTFE/PFA construction materials required for the flow path by the micro-e industry.

The weir style valve, if done properly, should provide a very good Cv – perhaps not as good as a stopcock/ball valve, but still very good. And although liquid orings are not an issue, these valves have other drawbacks. In a weir style valve the diaphragm is generally a sandwich structure consisting of a thin layer of PTFE that is backed by an elastomeric component in which a metal pin is embedded to connect the membrane to the valve actuating system. It is the sandwich materials that generate a number of potential issues when used on critical, high purity chemistry. Specifically, the delamination of the sandwich creates the possi- bility of multiple points of contamination to the liquid (metal & elastomer). In addition, the significant surface contact between the membrane and the valve seat, which is necessary to secure a full seal, generates a lot of particles – though significantly less than a stopcock/ball valve.

The diaphragm valve is the most commonly used valve in the semiconductor industry as it offers a great balance in terms of the issues previously identified: potential contami- nation, materials and particle generation. The trade-off is that the construction of these valves is more complex and as a result they are priced higher than the average cost of the other valves. Additionally, the Cv performance is well below a stopcock/ball valve and slightly below a weir style valve. However, by using Saint-Gobain’s patented rolling diaphragm technology this does not have to be an issue. In fact, with this technology, we can offer the equivalent Cv of a weir style valve in combination with premium pressure and temperature capabilities as well as the cleanest valve technology – all of which allows for a system design with the lowest impact possible on the transported fluid.

As demonstrated in this document, understanding the Cv rating and the impacts that could affect that rating as it relates to valves is critical when optimizing an installation for fluid and energy efficiency. Cost aside, there are a number of issues that are unique to the semiconductor industry that ultimately guide and often restrict installation choices, such as: dead volume, particle generation, cleanliness as well as the physical and mechanical properties of appropriate polymers. Additionally, choosing the appropriate valve for your installation goes far beyond the simple notion that if “I need more flow, I will get a larger valve.” Most likely the residual effect of that choice will affect the performance of the system, particularly regarding cleanliness. Instead critical adjustments to your valve actuation mechanism and valve flow path designs as well as to your valve technology may allow you to achieve the required results – even if the installation still uses the same 1⁄2” valve…but more on this point in another article.

References

1. www.processsystems.saint-gobain.com/sites/imdf.processsystems. com/files/2015-12-03-part-one-design-impact-for-fluid-components.pdf

POST A COMMENT

Easily post a comment below using your Linkedin, Twitter, Google or Facebook account. Comments won't automatically be posted to your social media accounts unless you select to share.